K-8000C Specifications
- Support 32-65536 level grayscale, correcting with software Gamma.
- Support various point, line and area light sources, various rules and special-shaped processing.
- Support 8 output ports, each can carry a maximum of 512/1024 lamps (DMX lamps with a maximum of 512 pixels take three channels as an example).
- The play content can be stored in SD card, which can store up to 32 effect files. The SD card capacity supports 128MB-32GB.
- The controller can be used alone or in cascade. The cascade adopts the photoelectric isolation method, featuring anti-interference and better stability. The cascade distance between two controllers can reach 150m by using pure copper power cord of 0.5 mm2.
- The controller with a loaded chip can be locked in the software with the loaded IC, or can be not locked and adjust the controller's "CHIP" button to select the loaded IC, which is more flexible and convenient.
- The IC controller for DMX lamps has its own address writing function; in addition, with our 2016 LedEdit-K V3.26 software or above version, you can set the one-key address writing function.
- Support 4-channel (RGBW) pixels or single-channel pixels for loading lamps.
- The built-in effect of the controller supports three channels (RGB) and four channels (RGBW).
- The controller supports MODBUS third-party control.
- Support enhanced TTL and 485 differential (DMX) signal output.
- The controller has 22 test effects and DMX512 channel test function.
Note: 1. The speed of 512 pixels of lamps on the controller can reach 30 frames/second, the speed of 768 pixels can reach 25 frames/second, and the speed of 1024 pixels can reach 22 frames/second
(The above parameters take the IC data of 1903 protocol as an example, and the data may be different for different ICs)
2. A maximum of 512 pixels of international standard DMX512 (1990 protocol) can be loaded. When the load is the international standard 170 pixels, the speed can reach 30 frames/second, the speed of 340 pixels is about 20 frames/second, and the speed of 512 pixels is about 12 frames/second.
3. If timing (holidays) play, Beidou WiFi synchronization and console channel distributor functions are required, please contact the sales personnel or the technical support personnel for details
|
|
|
|
① DC5V power input port ② DC12-24V input port ③ POWER/STATUS/SYNC indicator ④ SD card slot ⑤ MODBUS signal input port ⑥ Cascade IN A/B (satellite sync signal input port)/cascade OUT A/B ⑦ Signal output port OUT1-OUT8 |
|
1. One-key address: (as shown in the figure below: Step 1)
When the software writes the program output, click the key to enter the one-key address writing interface
2. Interval channel input (as shown in the figure below: Step 2)
The interval channel is input according to the actual number of the lamp, and the number is the number of channels occupied by a DMX512 IC control lamp pixel point.
3. Chip model selection (as shown in the figure below: Step 3)
Click the drop-down button to select the IC model corresponding to the DMX512 IC carried by the lamp.
4. Completing one-key address settings
After confirming that the settings are correct, click "SET" to complete the program output.
5. One-key code writing of controller
① Insert the SD card into the controller;
② Power on the controller;
③ Press and hold the "MODE" key for 5s, and the controller will display "Writing Addr…" and then "Writing OK" after writing;
④ After writing address, the controller will also enter the channel test mode (same as the channel test after manual address writing).
⑤ After completing channel testing, press "CHIP" to exit the test mode and return to the play mode for normal operation.
| Physical parameters: | Memory card: |
| Operating temperature: -20℃-75℃ | Type: SD card |
| DC 5V or DC 12-24V input | Capacity: 128MB-32GB |
| Power consumption: 5W | Format: FAT or FAT32 |
| Weight: 0.8Kg | Storage file: *.led |
| Dimensions: |  |
1. Before copying files to the SD card, the SD card must be first formatted. (Note that it must be formatted before each copying).
2. Format program
① SD card settings - "File System", "FAT" (SD card capacity ≤ 2G) or "FAT32" (SD card capacity ≧ 4G).
② SD Card Settings - "Allocation Unit Size", click the drop-down button to select "Default configuration size" or click "Restore default value of device".
③ Start formatting.
As shown in the figure below.
http://www.fsleds.com/