Price:Unfilled

Send inquiry

K-1000C Controller Specifications

 

 

Operating temperature: -30℃～85℃	Type: SD card
Operating power: DC 5V ‐24V input	Capacity: 128MB-32GB
Power consumption: 2W	Format: FAT or FAT32
Data transmission port: 3pin wiring terminal	Storage file: *.led
Weight: 0.35Kg	Dimensions: L159mm*W89mm*H24mmm

 

 

1. Support 32-65536 level grayscale, correcting with software Gamma.
2. Support various point, line and area light sources, various rules and special-shaped processing.
3. Support single output port, which can carry a maximum of 512 (DMX IC)/1536 (TTL/SPI) pixels (DMX lamps with a maximum of 512 pixels take three channels as an example).
4. The play content can be stored in SD card, which can store up to 32 effect files. The SD card capacity supports 128MB-32GB.
5. The controller can be used alone or in cascade. The cascade adopts the photoelectric isolation method, featuring anti-interference and better stability. The cascade distance between two controllers can reach 100m by using pure copper power cord of 0.5 mm².
6. The controller with a loaded IC can be locked in the software with the loaded IC, or can be not locked and adjust the controller's "IC" button to select the loaded IC, which is more flexible and convenient.
7. The IC controller for DMX lamps has its own address writing function; in addition, with our LedEdit-K software or above version, you can set the one-key address writing function.
8. Support 3/4/multiple-channel (RGBWYA) pixels or single-channel pixels for loading lamps.
9. The built-in effect of the controller supports three channels (RGB) and four channels (RGBW).
10. The controller can test the addresses of DMX512 lamps.
11. Support enhanced TTL and 485 differential (DMX) signal output.
12. The controller has 22 test effects and DMX512 test function.

 

Note: 1. The speed of 512 pixels of lamps on the controller can reach 30 frames/second, the speed of 1024 pixels can reach 25 frames/second, and the speed of 1536 pixels can reach 15 frames/second (The above parameters take the IC data of 1903 protocol as an example, and the data may be different for different ICs)

2. A maximum of 512 pixels of international standard DMX512 (1990 protocol) can be loaded. The speed can reach 30 frames/s when loading 170 pixels of international standard, about 20 frames/s when loading 340 pixels of international standard, and about 12 frames/s when loading 512 pixels.

 

 

 

1. Key meaning:

Key	Normal operation	Key function	Key combination function
CHIP	Switch the chip	NA	First press "CHIP" and then "MODE" to enter the Write Address interface; after writing, press "CHIP" and then "MODE" to exit the interface.
MODE	Switch the file	In the play interface, press and hold "MODE" to enter the DMX one-key address writing interface.
SPEED+	Speed up	Press "SPEED+" to power on and enter the built-in effect channel setting interface.	Press "SPEED+"/"SPEED-" simultaneously to enter the effect file cycle mode. If the screen displays C C C and flashes, it means the file cycle mode is entered.
SPEED-	Slow down	Press "SPEED-" to power on and enter the DMX channel testing interface.

 

2. Port meaning:

DC 5-24V	DC 5-24V power positive input	IN A	Cascade synchronous signal, connect to the OUTA of upper controller
GND	DC power negative input	IN B	Cascade synchronous signal, connect to the OUTB of upper controller
POWER	Power indicator	OUT A	Cascade synchronous signal, connect to the OUTA of lower controller
ERROR	Status indicator	OUT B	Cascade synchronous signal, connect to the IN B of lower controller
SD CARD	SD card slot
GND	Ground wire (negative)	B	Signal - (DAT-)
CLK	Clock line (address writing line for DMX lamps)	A	Signal+ (DAT+)
DAT	USB cable

 

3. Description of display content (6-digit display):

Display			Definition
1		F_F_F	Card reading error
2		A_A_A	DMX512 writing address
3		C_C_C	Effect cycle
4		2_2_2	Cascaded control
5		0_0_0	Enter DMX lamp address test/parameter writing
6		CH 3	Built-in effect three-channel settings (RGB)
7		CH 4	Built-in effect four-channel settings (RGBW)
8			Address writing interface Chip display: DMX512IC code 61-83 Mode display: Undefined Speed bit: Channel number 0-99
9			Play interface Chip display: Loading IC code 0-30 Mode display: Program sequence Speed bit: Level 1-16

 

4. Frame frequency of speed level:

Speed	Frame frequency/sec	Speed	Frame frequency/sec	Speed	Frame frequency/sec	Speed	Frame frequency/sec
1	4 frames	5	8 frames	9	14 frames	13	23 frames
2	5 frames	6	9 frames	10	16 frames	14	25 frames
3	6 frames	7	10 frames	11	18 frames	15	27 frames
4	7 frames	8	12 frames	12	20 frames	16	30 frames

 

 

Interval channel input

The interval channel is input according to the actual number of the lamp, and the number is the number of channels occupied by a DMX512 IC control lamp pixel point.

 

Chip model selection

Click the drop-down button to select the IC model corresponding to the DMX512 IC carried by the lamp.

Completing one-key address settings

After confirming that the settings are correct, click "SET" to complete the program output.

 

One-key code writing of controller

① Insert the SD card into the controller;

② Power on the controller;

③ Press and hold the "MODE" key for 5s, and the controller will display "A-A-A", that is writing address;

④ After writing address, the controller will also enter the channel test mode (same as the channel test after manual address writing).

⑤ After completing channel testing, press "CHIP" to exit the test mode and return to the play mode for normal operation.

 

http://www.fsleds.com/